Impulse6000D/7000DP

ภาพรวม
ลักษณะเด่น
ลักษณะเฉพาะ
ดาวน์โหลด

The Impulse 6000D Defibrillator Analyzer and Impulse 7000DP Defibrillator/Transcutaneous Pacer Analyzer Test Systems are rugged, portable precision test instruments that ensure proper operation and ultimate performance of critical life-support cardiac-resuscitation equipment.

The Impulse 6000D and Impulse 7000DP test capabilities encompass the spectrum of worldwideestablished pulse shapes, showcase breakthrough AED technology compatibility, and outperform in accuracy and standards. Additionally, the Impulse 7000DP incorporates the tests and the extensive range of test loads and measurement algorithms needed to test external transcutaneous pacemakers.

In conjunction with an Impulse 7000DP, the Impulse 7010 Defibrillator Selectable Load Accessory provides multiple loads of 25 Ω, 50 Ω, 75 Ω, 100 Ω, 125 Ω, 150 Ω, 175 Ω and 200 Ω for defibrillator performance testing. A standard USB interface enables computer control and data transfer, and optional Ansur PC-based automation software increases productivity by outfitting users with an easy-to-use method to standardize testing procedures and capture, print and document data.

Key Features

Impulse 7010 Defibrillator Selectable Load Accessory provides multiple loads of 25 Ω, 50 Ω, 75 Ω, 100 Ω, 125 Ω, 150 Ω, 175 Ω, and 200 Ω to comply with IEC 60601-2-4 standard (optional)
Lown, Edmark, trapezoidal, biphasic and pulsed-biphasic defibrillation technology compatibility
AED technology compatibility
First-class measurement accuracy ± 1 % of reading + 0.1 J
Intuitive user interface and backlight, easy-to-read display
Portable, rugged, easy to carry
Long-lasting, rechargeable battery
Pacer brand selections
Pacer input protected against defibrillator output (7000DP only)
10 independent ECG outputs that provide 12 lead combinations for standardized clinical signals
Flexible heart-rate settings (1 BPM step) facilitate rate meter accuracy and alarm testing
DSP-based measurements enable future firmware and waveforms upgrade
Unique integrated posts for secure connections
Two-year extended warranty (no-cost extended warranty available after first-year calibration at any Fluke Biomedical authorized service center)
Optional Ansur test automation software to standardize testing procedures, capture waveforms and test results, and print and document test results
Designed, tested, and built to incomparable Fluke quality standards

General Specifications

Temperature, operating	10 °C to 40 °C (50 °F to 104 °F)
Temperature, storage	-20 °C to +60 °C (-4 °F to +140 °F)
Humidity	10 % to 90 % non-condensing
Display	LCD display
Communications	USB device port for computer control
Modes of operation	Manual and remote
Power	Internal rechargeable NiMH battery pack for nine hours (typical) operation after full charge or the battery charger can operate the analyzer and charge the battery simultaneously
Battery charger	100 V to 240 V input, 15 V/1.5 V A output. For best performance, the battery charger should be connected to a properly grounded ac receptacle
Enclosure	ABS plastic housing
Dimensions	32 cm x 24 cm x 13 cm
	(13 in x 9.5 in x 5 in)
Weight	3.02 kg (6.6 lb, 0.1 oz)
Safety standards	CE: IEC/EN61010-1 2nd Edition; Polution degree 2 CAN/CSA-C22.2 No. 61010-1; UL61010-1 C-Tick: Australian EMC

Defibrillator Analyzer Specifications
Energy Output Measurement

Compatible Defibrillator Waveshapes

	Lown, Edmark, Trapezoidal, DC Bi-phasic, and AC Pulsed Bi-phasic
	AC Pulsed Biphasic waveform has not been approved in the United States.

Autoranged Measurement

0.1 J to 600 J

Accuracy

0.1 J to 360 J	± (1 % of reading + 0.1 J)
360 J to 600 J	± (1 % of reading + 0.1 J), typical
	Note: For Pulsed Bi-Phasic defibrillator, specified accuracy is ±(1.5 % of reading + 0.3 J) on both ranges.

Load resistance

Resistance	50 Ω
Accuracy	±1 %, non-inductive (<2 µH)

Pulse trigger level

20 V

Pulse width

Range	1 ms to 50 ms
Accuracy	±0.1 ms

Voltage

Range	20 V to 5000 V
Accuracy	± (1 % of reading + 2 V)

Current

Range	0.4 A to 100 A
Accuracy	± (1 % of reading + 0.1 A)

Tilt (biphasic and pulsed biphasic)

Range	1 % to 99 %
Accuracy	± 1 digit

Interphase delay (biphasic and pulsed biphasic)

Range	0.1 ms to 9.9 ms
Accuracy	± 0.1 ms

Frequency (pulsed biphasic only)

Range	2000 Hz to 8000 Hz
Accuracy	± 1 % of reading

Duty cycle (pulsed biphasic only)

Range	1 % to 99 %
Accuracy	± digit

Sample rate

250 kHz (4 µs sample)

Maximum Average Power

12 W, equivalent to 10 defib pulses of 360 J every 5 minutes

Scope Output

Autorange:2000:1, 400:1 and 80:1: dependant on the range

Waveform Playback

Output: BNC
Output impedance: 50 Ω
Amplitude Accuracy: ± 5 %

Charge Time Measurement

Range	0.1 s to 100 s
Accuracy	± 0.05 s, typical

Synchronization Test (Elective Cardioversion)

Delay Time Measurement	Timing window: : ECG R-wave peak to the defib pulse peak
	Range: -120 to +380 ms; measures timing from 120 ms prior to the R-wave peak to up to 380 ms following the R-wave peak
	Resolution: 1 ms
	Accuracy: ± 1 ms
ECG waves	Normal Sinus Rhythm (NSR): 10 BPM to 180 BPM, in 1 BPM steps
	Atrial fibrillation: Coarse and fine
	Monomorphic Ventricular Tachycardia: 120 BPM to 240 BPM, in 5 BPM steps
	Asystole: Flat line

Automated Defibrillator Test ECG Waves

Normal Sinus	10 BPM to 300 BPM, in 1 BPM steps
Ventricular Fibrillation	Coarse and fine
Monomorphic Ventricular Tachycardia	120 BPM to 300 BPM, in 5 BPM steps
Polymorphic Ventricular Tachycardia	5 types
Asystole	Flat line

ECG Waves

ECG General

Lead configuration	12-lead simulation. RA, LL, LA, RL, V1-6 with independent signal outputs
Lead-to-lead impedance	1000 Ω (nominal)
Rate accuracy	± 1 % of nominal

ECG Amplitudes

Reference lead	Selectable, Lead II (default) or Lead 1
Settings	0.05 mV to 0.45 mV, in 0.05 mV steps 0.5 mV to 5 mV, in 0.5 mV steps
Accuracy (All Performance waves and Normal Sinus R waves)	Lead II: ± 2 % All other leads: ± 5 % Defib paddles: ± 5 %
Amplitude of ECG signals relative to amplitude setting (in percent)	Lead II reference:
	Performance waves and R wave detection
	Lead I – 70 %
	Lead II – 100 %
	Lead III – 30 %
	Lead V1 – 100%
	Lead V2 – 100%
	Lead V3 – 100 %
	Lead V4 – 100 %
	Lead V5 – 100 %
	Lead V6 – 100 %
	Normal Sinus waves
	Lead I – 70 %
	Lead II – 100 %
	Lead III – 30 %
	Lead V1 – 24%
	Lead V2 – 48%
	Lead V3 – 100 %
	Lead V4 – 120 %
	Lead V5 – 112 %
	Lead V6 – 80 %
	Lead I reference:
	Performance waves and R wave detection
	Lead I – 100 %
	Lead II – 150 %
	Lead III – 50 %
	Lead V1 – 100%
	Lead V2 – 100%
	Lead V3 – 100 %
	Lead V4 – 100 %
	Lead V5 – 100 %
	Lead V6 – 100 %
	Normal Sinus waves
	Lead I – 100 %
	Lead II – 150 %
	Lead III – 50 %
	Lead V1 – 24%
	Lead V2 – 48%
	Lead V3 – 100 %
	Lead V4 – 120 %
	Lead V5 – 112 %
	Lead V6 – 80 %

ECG Normal sinus

Rates

10 BPM to 360 BPM, in 1 BPM steps

ECG High level output (BNC Jack)

Amplitude Range	0.5 V/mV of reference lead setting
Accuracy	± 5 %
Output Impedance:	50 Ω

ECG on defibrillator Input Load

Same as the Lead II amplitude but limited to ± 4 mV

ECG Performance Waves

Square wave	2 Hz and 0.125 Hz
Triangular wave	2 Hz and 2.5 Hz
Sine waves	0.05, 0.5, 5, 10, 40, 50, 60, 100, 150, and 200 Hz
Pulse	30BPM and 60 BPM, 60 ms pulse width

R-Wave detection

Waveform	Haver-triangle
Rates	30, 60, 80, 120, 200 and 250 BPM
Widths	8, 10, 12 and 20 to 200 (by 10) ms
Amplitudes	0.05 mV to 0.45 mV 0.05 mV hard return
	0.5 mV to 5 mV, in 0.5 mV steps
Accuracy	± (1 % setting + 1 ms)

Noise Immunity

Wave	Sine
Line Frequency	50 Hz or 60 Hz ( ± 0.5 Hz)
Amplitude	Range: 0.0 mV to 10 mV, in 0.5 mV steps
	Accuracy: ± 5 %

Transvenous Pacer Pulse Simulation

Widths	Range: 0.1, 0.2, 0.5, 1, and 2 ms.
	Accuracy: ± 5 % of setting
Amplitudes	Range: 0 (off) and ± 2, ± 4, ±6, ±8, ±10, ±12. ±14, ±16, ±18, ±20, ±50, ±100, ±200, ±500, ±700 mV
	Accuracy: ± (10 % setting + 0.2 mV)
Amplitude of Transvenous Pacer Pulse Simulation signals relative to amplitude setting (in percent)	Lead II reference:
	Lead I – 67 %
	Lead II – 100 %
	Lead III – 33 %
	Lead V1 – 67%
	Lead V2 – 67%
	Lead V3 – 67 %
	Lead V4 – 67 %
	Lead V5 – 67 %
	Lead V6 – 67 %
	Lead I reference:
	Lead I – 100 %
	Lead II – 150 %
	Lead III – 50 %
	Lead V1 – 100%
	Lead V2 – 100%
	Lead V3 – 100 %
	Lead V4 – 100 %
	Lead V5 – 100 %
	Lead V6 – 100 %

Arrhythmia selections

Pacer Interactive (Transcutaneous Pacer, Impulse 7000DP only)	Demand: 30 BPM to 360 BPM, in 1 BPM steps Asynchronous Non-Capture Non-Function Threshold (interactive pacing simulation only): 10 mA to 250 mA in 10 mA steps
Supraventricular	Atrial Fibrillation Coarse Atrial Fibrillation Fine Atrial Flutter Sinus Arrhythmia Missed Beat Atrial Tachycardia Paroxysmal Atrial Tachycardia Nodal Rhythm Supraventricular Tachycardia
Premature	Atrial PAC Nodal PNC PVC1 Left Ventricle (LV) PVC1 Left Ventricle (LV) Early PVC1 Left Ventricle (LV) R on T PVC2 Right Ventricle (RV) PVC2 Right Ventricle (RV) Early PVC2 Right Ventricle (RV) R on T Multifocal PVCs (LV and RV)
Ventricular	PVCs 6/min PVCs 12/min PVCs 24/min Freq Multifocal Trigeminy Bigeminy Pair PVCs Run 5 PVCs Run 11 PVCs Monomorphic VTach: 120 to 300 (5 BPM steps) Polymorphic VTach: 5 selections Ventricular Fibrillation: Coarse and Fine Asystole
Conduction	1° Block 2° Block Type I 2° Block Type II 3° Block Right Bundle Branch Block (RBBB) Left Bundle Branch Block (LBBB)
Transvenous Pacemaker (ECG simulation only)	Atrial 80 BPM Asynchronous 75 BPM Demand with frequent sinus beats Demand with occasional sinus beats AV Sequential Non-Capture Non-Function

Selectable pacer pulse parameters for transvenous simulation (Atrial & Ventricular channels are independently selectable by the user)

Atrial Pacer Pulse (Note: relates only to the TV pacer)	Width: 0.1, 0.2, 0.5, 1, 2 ms Polarity: + or - Amplitude: 0 (off), 2 to 20 (by 2), 50, 100, 200, 500, 700 mV
Ventricular Pacer Pulse (Note: relates only to the TV pacer)	Width: 0.1, 0.2, 0.5, 1, 2 ms Polarity: + or - Amplitude: 0 (off), 2 to 20 (by 2), 50, 100, 200, 500, 700 mV

(BNC Jack)

Accuracy

± 5 % for 2 Hz Square Wave , 50 _ output impedance

Transcutaneous Pacemaker Analyzer Specifications (7000DP only)

Test Load Selections

Defibrillator Input	Fixed load: 50 Ω Accuracy: ± 2 %, non-inductive (<2 μH) Power rating: 10 defib pulses of 360 J every 5 minutes
Pacemaker Input	Variable load: 50 Ω to 1500 Ω in 50 Ω steps Accuracy: ± 2 %, non-inductive (< 2 µH) Power rating: 5 W (average), 40 W (peak) @ 1000 Ω

Measurements

Manufacturer specific algorithms	GE Responder (1500 & 1700) MDE 300 (Medical Data Electronics) Medtronic ERS/Physio Control LIFEPAK MRL (Medical Research Laboratory/Welch Allyn) Philips/Agilent HP Schiller Medical ZOLL Medical (plus a general purpose Default Algorithm selection)
Current	4 to 250 mA, ± (1% of reading + 0.02 mA)
Pulse rate	5 to 800 PPM, ± (0.5% of reading + 0.1 PPM)
Pulse width	1 to 100 ms, ± (0.5% of reading + 0.01 ms)
Energy	1 μJ to 2 J, ± (4% of reading + 10 μJ)

Demand and Asynchronous Mode Test

Input pacer pulse rates	30 to 200 PPM
ECG NSR wave	Rate:10 to 300 BPM in 1 BPM increments. Amplitude:1 mV Underdrive rate:10 BPM minimum Overdrive rate:300 BPM maximum

Sensitivity Test

Automatic interactive threshold detection	Compatible pacer rates: 30 to 120 PPM.
ECG R Wave	Waveforms:Square, Triangle, Sine Width:1 to 19 (by 1) ms. 20 to 95 (by 5) ms. 100 to 300 (by 25) ms Amplitude:0.05 to 0.95 (by 0.05) mV. 1 to 5 (by 0.5) mV Accuracy:± 5% of setting

Refractory Period Tests

Paced Refractory Period	20 to 500 ms
Sensed Refractory Period	15 to 500 ms
Accuracy	± 1 ms
Pacer pulse rate	20 to 200 PPM
ECG	Waveform:Triangle wave Pulse Width:40 ms Amplitude:1 mV

Impulse 7010 Defibrillator Selectable Load Accessory*

General specifications

Maximum voltage	5000 V
Maximum continuous power	12 W. equivalent to 10 defib pulses of 360 J every 5 minutes
Inductance	< 2 µH, @25 Ω
	< 3 µH, @50 Ω
	< 4 µH, @75 Ω and 100 Ω
	< 5 µH, @125 Ω
	< 6 µH, @150 Ω
	< 7 µH, @175 Ω
	< 8 µH, @200 Ω
Temperature	Operating: 10 ºC to 40 ºC (50 ºF to 104 ºF)
	Storage: -20 ºC to 60 ºC (-4 ºF to 140 ºF)
Humidity	10 % to 90 % non-condensing
Dimensions (WxDxH)	154 mm x 272 mm x 138.7 mm
	(6.07 in x 10.71 in x 5.46 in)
Weight (net)	1.54 kg (3 lb 6.2 oz)
Safety class	Complies with EN61010-1 2nd Edition, Class II product
Safety and EMC marks	CE, CSA, and C-Tick
Warranty	2-year extended warranty (no-cost extended warranty available after first-year calibration at any Fluke Biomedical authorized service center)
Calibration intervalq	1 year

Electrical specifications (for Load Accessory and Analyzer together)

Load settings	25 Ω, 50 Ω, 75 Ω, 100 Ω, 125 Ω, 150, Ω, 175 Ω, and 200 Ω ± 1 %
Accuracy	Energy (all except pulsed biphasic): 2 % o reading + 0.1 J with 25, 75 Ω through 200 Ω loads, 1 % of reading + 0.1 J with 50 Ω load
	Energy (pulsed biphasic): 2.5 % or reading + 0.3 J with 25, 75 Ω through 200 Ω loads, 1.5 % of reading + 0.3 J with 50 Ω load
	Voltage: 1 % of reading + 2 V with 25 Ω and 50 Ω loads, 2 % of reading + 2 V with 75 Ω through 200 Ω loads
	Current: 2 % or reading + 0.1 A with 25 Ω load, 1 % of reading + 0.1 A with 50 Ω through 200 Ω loads

แคตาล็อค Impulse 6000D / 7000DP

ตัวอย่าง Report

คู่มือการใช้งาน Impulse 6000D / 7000DP